Fluke MET/CAL Procedure ============================================================================= INSTRUMENT: Sanwa 9600EA: CAL ADJ /5520 DATE: 09-Sep-97 AUTHOR: Fluke Corporation REVISION: $Revision: 1.1 $ ADJUSTMENT THRESHOLD: 70% NUMBER OF TESTS: 1 NUMBER OF LINES: 219 CONFIGURATION: Fluke 5520A ============================================================================= # # Compatibility: # 5500/CAL 5.0 or MET/CAL 5.0 or later. # # Subprocedures: # None # # Required Files: # None # # System Specifications: # TUR calculation is based on specification interval of the accuracy file. # The default 5520A accuracy file contains 90 day specs. # # Fluke makes no warranty, expressed or implied, as to the fitness # or suitability of this procedure in the customer's application. # STEP FSC RANGE NOMINAL TOLERANCE MOD1 MOD2 3 4 CON 1.001 DISP Procedure not formally tested with UUT. 1.001 DISP See procedure README file. 1.002 ASK- V 1.003 HEAD PRELIMINARY INSTRUCTIONS 1.004 DISP Warm-up time: 30 min. - REQUIRED 1.004 DISP Temperature: 22 - 24 degC 1.004 DISP Humidity: <70% 1.005 DISP [32] WARNING 1.005 DISP HIGH VOLTAGE is used or exposed during the performance 1.005 DISP of this calibration. DEATH ON CONTACT may result if 1.005 DISP personnel fail to observe safety precautions. 1.006 DISP To prevent a shock hazard, remove all test leads from 1.006 DISP the instrument and turn the instrument OFF before 1.006 DISP disassembling the Model 9600EA 1.007 HEAD PREPARATION 1.008 DISP Check that adjustment-slide-switch on horizontal PCB 1.008 DISP of 9600EA is set to FIX-side. The slide switch is 1.008 DISP located at rear most side of PCB where shield plate is 1.008 DISP notched. 1.009 DISP Turn on power while pressing all the keys: 1.009 DISP RANGE, HOLD, REL, and RATE. 1.010 DISP Set the adjustment-slide-switch on the horizontal 1.010 DISP PCB of 9600EA to CAL-side. 1.011 DISP CAUTION 1.011 DISP Return the slide-switch to FIX-side when power is to 1.011 DISP be turned off before, or after adjustment is made. 1.011 DISP 1.011 DISP Adjustment should be done under 39999 count mode. 1.012 HEAD ZERO POINT 1.013 DISP Connect the 5520A to the UUT as follows: 1.013 DISP [32] 5520A NORMAL HI to UUT V/mA/Ohm 1.013 DISP [32] 5520A NORMAL LO to UUT COM 1.014 RNG 400mV 1.015 5520 0V S 2W 1.016 DISP Adjust VDC "Zero" by pressing HOLD key while changing 1.016 DISP the range from 400mV to 500V. 1.017 5520 * S 1.018 RNG 400mV AC 1.019 5520 0V S 2W 1.020 DISP Adjust VAC "Zero" by pressing HOLD key while changing 1.020 DISP the range from 400mV to 500V. 1.021 5520 * S 1.022 RNG 400Z # 2 wire comp. uncecessary since lead resistance is zeroed at uut. 1.023 ASK- U 1.024 5520 0.0Z S 2W 1.025 ASK+ U 1.026 DISP Adjust OhmS "Zero" by pressing HOLD key while changing 1.026 DISP the range from 400ohm to 40Mohm. 1.027 5520 * S 1.028 RNG 40mA 1.029 5520 0.0mA S 2W 1.030 DISP Adjust mA DC "Zero" by pressing HOLD key while changing 1.030 DISP the range from 40mA to 400mA. 1.031 5520 * S 1.032 RNG 40mA AC 1.033 5520 0.0mA S 2W 1.034 DISP Adjust mA AC "Zero" by pressing HOLD key while changing 1.034 DISP the range from 40mA to 400mA. 1.035 5520 * S 1.036 DISP Connect the 5520A to the UUT as follows: 1.036 DISP [32] 5520A AUX HI to UUT 10A 1.036 DISP [32] 5520A AUX LO to UUT COM 1.037 RNG 10A 1.038 5520 0mA S 2W 1.039 DISP Adjust 10A DC "Zero" by pressing HOLD key. 1.040 5520 * S 1.041 RNG 10A AC 1.042 5520 0mA S 2W 1.043 DISP Adjust 10A AC "Zero" by pressing HOLD key. 1.044 5520 * S 1.045 HEAD FULL SCALE 1.046 DISP Connect the 5520A to the UUT as follows: 1.046 DISP [32] 5520A 20A to UUT 10A 1.046 DISP [32] 5520A AUX LO to UUT COM 1.047 RNG 10A 1.048 5520 10A HC S 2W 1.049 DISP Press REL key. 1.050 5520 * S 1.051 5520 -10A HC S 2W 1.052 DISP Press RATE key. 1.053 5520 * S 1.054 DISP Connect the 5520A to the UUT as follows: 1.054 DISP [32] 5520A NORMAL HI to UUT V/mA/Ohm 1.054 DISP [32] 5520A NORMAL LO to UUT COM 1.055 RNG 400mV 1.056 5520 380mV S 2W 1.057 DISP Press REL key. 1.058 5520 -380mV S 2W 1.059 DISP Press RATE key. 1.060 5520 * S 1.061 RNG 4V 1.062 5520 3.8V S 2W 1.063 DISP Press REL key. 1.064 5520 -3.8V S 2W 1.065 DISP Press RATE key. 1.066 5520 * S 1.067 RNG 40V 1.068 5520 38V S 2W 1.069 DISP Press REL key. 1.070 5520 -38V S 2W 1.071 DISP Press RATE key. 1.072 5520 * S 1.073 RNG 400V 1.074 5520 380V S 2W 1.075 DISP Press REL key. 1.076 5520 -380V S 2W 1.077 DISP Press RATE key. 1.078 5520 * S 1.079 RNG 500V 1.080 5520 500V S 2W 1.081 DISP Press REL key. 1.082 5520 -500V S 2W 1.083 DISP Press RATE key. 1.084 5520 * S 1.085 DISP Connect the 5520A to the UUT as follows: 1.085 DISP [32] 5520A AUX HI to UUT V/mA/Ohm 1.085 DISP [32] 5520A AUX LO to UUT COM 1.086 RNG 40mA 1.087 5520 38mA S 2W 1.088 DISP Press REL key. 1.089 5520 -38mA S 2W 1.090 DISP Press RATE key. 1.091 5520 * S 1.092 RNG 400mA 1.093 5520 380mA S 2W 1.094 DISP Press REL key. 1.095 5520 -380mA S 2W 1.096 DISP Press RATE key. 1.097 5520 * S 1.098 DISP Connect the 5520A to the UUT as follows: 1.098 DISP [32] 5520A NORMAL HI to UUT V/mA/Ohm 1.098 DISP [32] 5520A NORMAL LO to UUT COM 1.099 RNG 400mV AC 1.100 5520 380mV 60H SI S 2W 1.101 DISP Press REL key. 1.102 5520 * S 1.103 RNG 4V AC 1.104 5520 3.8V 60H SI S 2W 1.105 DISP Press REL key. 1.106 5520 * S 1.107 RNG 40V AC 1.108 5520 38V 60H SI S 2W 1.109 DISP Press REL key. 1.110 5520 * S 1.111 RNG 400V AC 1.112 5520 380V 60H SI S 2W 1.113 DISP Press REL key. 1.114 5520 * S 1.115 RNG 500V AC 1.116 5520 500V 60H SI S 2W 1.117 DISP Press REL key. 1.118 5520 * S 1.119 DISP Connect the 5520A to the UUT as follows: 1.119 DISP [32] 5520A AUX HI to UUT V/mA/Ohm 1.119 DISP [32] 5520A AUX LO to UUT COM 1.120 RNG 40mA AC 1.121 5520 38mA 60H SI S 2W 1.122 DISP Press REL key. 1.123 5520 * S 1.124 RNG 400mA AC 1.125 5520 380mA 60H SI S 2W 1.126 DISP Press REL key. 1.127 5520 * S 1.128 DISP Connect the 5520A to the UUT as follows: 1.128 DISP [32] 5520A AUX HI to UUT V/mA/Ohm 1.128 DISP [32] 5520A AUX LO to UUT COM 1.128 DISP [32] 5520A NORMAL HI to UUT V/mA/Ohm 1.128 DISP [32] 5520A NORMAL LO to UUT COM 1.128 DISP Connect the SENSE leads DIRECTLY to the UUT. Connect 1.128 DISP the NORMAL leads to the SENSE leads AT the UUT. 1.129 RNG 400Z 1.130 5520 380Z S CW 1.131 DISP Press REL key. 1.132 RNG 4kZ 1.133 5520 3.8kZ S CW 1.134 DISP Press REL key. 1.135 RNG 40kZ 1.136 5520 38kZ S CW 1.137 DISP Press REL key. 1.138 RNG 400kZ 1.139 5520 380kZ S 2W 1.140 DISP Press REL key. 1.141 RNG 4MZ 1.142 5520 3.8MZ S 2W 1.143 DISP Press REL key. 1.144 RNG 40MZ 1.145 5520 38MZ S 2W 1.146 DISP Press REL key. 1.147 END